FeelFree Transom Kayak Motor for Lure - Moken Kayaks
|
Island Hopper Kayak Transom Trolling Motors for FeelFree Lure & FeelFree Moken Kayaks
|
|
Conventional Trolling Motors are the most commonly used motor for boating and kayaking. They are cost affective and are equipped with 5 forward / 2 reverse speeds. They are primarily designed to propel you quickly to your desired destination or fishing hole, and then reposition your boat or kayak when currents or wind blow you off course.
Understanding Conventional Speeds: - 1st and 2nd speeds are designed for “short bursts” only, not to exceed 15 minutes intervals at a time. "Not for trolling", as it will damage these two speeds. - 3rd speed is for covering larger areas, traveling and mostly getting around while conserving battery. - 4th speed is for traveling longer distances faster. - 5th speed is for when speed is required, such as a change in the weather, current, chop waters or an emergency; getting to safety or shore quickly. Battery Compatibility: Deep Cycle Marine, AGM and GEL batteries. Conventional trolling motors are Not compatible with Lithium-Ion / LiFePO4 batteries |
Transom Mount Trolling Motor 55 lb Thrust on FeelFree Lure II
|
Transom Mount Kits - Navigate with Steering Handle
Transom Mount Conventional Trolling Motor - Navigate with Steering Handle
Item # 68-7761 Includes conventional trolling motor with customized mounting bracket, remote controller with 5 speeds forward and 3 speeds reverse, telescoping steering handle, motor lifting cord kit, and all stainless steel hardware required for installation. Zinc anode on salt water models only. No access hatch required. Fits Lure II, Lure 10, Lure 11.5, Moken 10 Lite, Moken 10 Standard, Angler, Move Angler . The Moken 12.5 will only mount to kayak, can not be used with track clips. Battery Type: Deep Cycle Marine, AGM & Gel Batteries Only Note: Remote control is hand held. (Optional Mounting Bracket Sold Separately) This installation requires the screwing the mounting brackets to kayak. If track installation is preferred, you'll need to add to your order item # 33-5870 (below). For V2 models Click Here |
|
Transom Mount Conventional Trolling Motor w/ 35ah AGM Battery- Navigate with Steering Handle
Item # 68-2214 Includes conventional trolling motor with customized mounting bracket, remote controller with 5 speeds forward and 3 speeds reverse, telescoping steering handle, motor lifting cord kit, 35ah AGM battery, and all stainless steel hardware required for installation. Zinc anode on salt water models only. No access hatch required. Fits Lure II, Lure 10, Lure 11.5, Moken 10 Lite, Moken 10 Standard, Angler, Move Angler . The Moken 12.5 will only mount to kayak, can not be used with track clips. Battery Type: Deep Cycle Marine, AGM & Gel Batteries Only Note: Remote control is hand held. (Optional Mounting Bracket Sold Separately) This installation requires the screwing the mount to kayak. If track installation is preferred, you'll need to add to your order item # 33-5870 (below). For V2 models Click Here |
|
**Coast Guard requirements dictate that each ungrounded current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse**
Transom Mount Kits - Navigate with Foot Pedal - Rudder Cables Required
Transom Mount Conventional Trolling Motor - Navigate with Foot Pedals
Item # 68-2500 Includes conventional trolling motor with customized mounting bracket, remote controller with 5 speeds forward and 3 speeds reverse, motor lifting cord kit, and all stainless steel hardware required for installation. Zinc anode on salt water models only. No access hatch required. Fits Lure II, Lure 10, Lure 11.5, Moken 10 Lite, Moken 10 Standard, Angler, Move Angler . The Moken 12.5 will only mount to kayak, can not be used with track clips. Attaches to Rudder Cables for Navigating with Foot Pedals Battery Type: Deep Cycle Marine, AGM & Gel Batteries Only Note: Remote control is hand held. (Optional Mounting Bracket Sold Separately) This installation requires the screwing the mount to kayak. If track installation is preferred, you'll need to add to your order item # 33-5870 (below), For V2 models Click Here |
|
Transom Mount Conventional Trolling Motor w/ 35 AGM Sealed Battery - Navigate with Foot Pedal
Item # 68-2521 Includes conventional trolling motor with customized mounting bracket, remote controller with 5 speeds forward and 3 speeds reverse, motor lifting cord kit, 35ah AGM battery and all stainless steel hardware required for installation. Zinc anode on salt water models only. No access hatch required. Fits Lure II, Lure 10, Lure 11.5, Moken 10 Lite, Moken 10 Standard, Angler, Move Angler . The Moken 12.5 will only mount to kayak, can not be used with track clips. Attaches to Rudder Cables for Navigating with Foot Pedals Battery Type: Deep Cycle Marine, AGM & Gel Batteries Only Note: Remote control is hand held. (Optional Mounting Bracket Sold Separately) This installation requires the screwing the mount to kayak. If track installation is preferred, you'll need to add to your order item # 33-5870 (below) For V2 models Click Here |
|
**Coast Guard requirements dictate that each ungrounded current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse**
|
Variable Speed Trolling Motors are one of the most improved technology today. Boaters and kayakers are gravitating to trolling motors with variable speeds due to their many benefits,
Benefits of Variable Speed Include: - Infinite Speed Range of "0-100 speed forward and reverse", which allows for trolling at very low speeds for hours without affecting any speeds of motor. - A Micro Processer aka (Pulse Width Modulator) to increase battery range 3 to 4 times, allowing for hours of continuous trolling. - Controlled Amperage provides steady trolling in currents and wind while conserving battery at 95% efficiency. - Integrated Electronic Board System senses over and undercharge of voltage, eliminates voltage spikes, 95% efficiency in power and torque. - Soft start: no spooking of fish while trolling and lighter in weight than conventional trolling motors, Battery Compatible: Lithium-Ion / LiFePO4, Deep Cycle Marine, AGM and GEL batteries. |
Transom Mount Trolling Motor 55 lb Thrust on FeelFree Lure II
|
Lithium Iron - LiFeP04 Compatible Trolling Motors
These motors are designed to be used with LiFeP04 battery and built with an intergraded circuit board which regulates the voltage and allows speed adjustments in fractional increments, from 1/4 to 5 mph. This motor includes heavy gauged wire, auto reset fuse, lithium-ion plug, which handles 60 to 200 amp LiFePO4 batteries.
These motors are designed to be used with LiFeP04 battery and built with an intergraded circuit board which regulates the voltage and allows speed adjustments in fractional increments, from 1/4 to 5 mph. This motor includes heavy gauged wire, auto reset fuse, lithium-ion plug, which handles 60 to 200 amp LiFePO4 batteries.
Transom Variable Speed Trolling Motor - Navigate w/ Steering Handle
Item # 68-07761-VS-LITH Includes trolling motor with intergraded circuit board, customized mounting bracket, handheld remote with infinite forward and reverse speed, heavy gauged battery cable, lithium ion plug, telescoping steering handle, motor lifting cord kit and all stainless steel hardware required for installation. Zinc anode on salt water models only. Fits Lure II, Lure 10, Lure 11.5, Moken 10 Lite, Moken 10 Standard, Angler, Move Angler . The Moken 12.5 will only mount to kayak, can not be used with track clips. Battery Type: LiFeP04, Deep Cycle Marine, AGM & Gel Batteries Note: Remote control is hand held. (Optional Mounting Bracket Sold Separately) (See Below) This installation requires the screwing the mount to kayak. If track installation is preferred, you'll need to add to your order item # 33-5870 (below) For V2 models Click Here |
|
|
Transom Variable Speed Trolling Motor - Navigate with Foot Pedal
Item # 68-02500-VS-LITH Includes trolling motor with intergraded circuit board, customized mounting bracket, handheld remote with infinite forward and reverse speed, heavy gauged battery cable, lithium ion plug, motor lifting cord kit and all stainless steel hardware required for installation. Zinc anode on salt water models only. Fits Lure II, Lure 10, Lure 11.5, Moken 10 Lite, Moken 10 Standard, Angler, Move Angler . The Moken 12.5 will only mount to kayak, can not be used with track clips. Attaches to Rudder Cables for Navigating with Foot Pedals. Battery Type: LiFeP04, Deep Cycle Marine, AGM & Gel Batteries Note: Remote control is hand held. (Optional Mounting Bracket Sold Separately) (See Below) This installation requires the screwing the mount to kayak. If track installation is preferred, you'll need to add to your order item # 33-5870 (below) For V2 models Click Here |
|
Understanding Lithium-Ion (LiFePO4) Battery & Their Effect On Conventional Trolling Motors vs Trolling Motors with Intergraded Circuit Board
LiFePO4 batteries were designed to be light weight and pack more energy. LiFePO4 batteries were engineered to store as much voltage from solar panels.
The stored voltage is unregulated and will burnout conventional trolling motors or shorten their lifespan, because the collected volts are too high (+18 volts = 12.8 - 16.0 volts DC), whereas conventional trolling motors operate on regulated 12 volts. Therefore, to regulate the LiFePO4 batteries voltage output, a trolling motor requires an intergraded circuit board to control speed and regulate the voltage, along with a heavy gauged battery cable, lithium-ion plug and an auto reset fuse.
Trolling motors with intergraded circuit board tend to have a longer lifespan and extended fishing time while kayaking. Read More
LiFePO4 batteries were designed to be light weight and pack more energy. LiFePO4 batteries were engineered to store as much voltage from solar panels.
The stored voltage is unregulated and will burnout conventional trolling motors or shorten their lifespan, because the collected volts are too high (+18 volts = 12.8 - 16.0 volts DC), whereas conventional trolling motors operate on regulated 12 volts. Therefore, to regulate the LiFePO4 batteries voltage output, a trolling motor requires an intergraded circuit board to control speed and regulate the voltage, along with a heavy gauged battery cable, lithium-ion plug and an auto reset fuse.
Trolling motors with intergraded circuit board tend to have a longer lifespan and extended fishing time while kayaking. Read More
Customers Who Bought This Item Also Bought
|
Item # 33-4567
Mounting Bracket for Remote Control. Mounts to kayak, allows remote control to pivot for ease of use. Includes two stainless steel self-tapping screws. This item can only be ordered when ordering any transom trolling kits. |
Sale Price $12.99
|
|
Item # 33-4509
Cord Guide for Lift Kit Cord. Cord bracket guide mounts to kayak, assists the lift cord by keeping the cord in place. Includes two stainless steel self-tapping screws. |
Sale Price $7.99
|
|
Item # 33-8765
Auto Reset Fuse - Protect your investment with an Auto Reset Fuse. High quality reset circuit breaker. These circuit breakers feature an automatic self-reset. **Coast Guard requirements dictate that each ungrounded current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse. |
Sale Price $19.99
|
|
Item # 33-5870 (Optional)
Universal Track Mounting Clips for FeelFree kayaks with track system. Island Hopper Transom Mount Trolling motors can be installed into FeelFree track ,instead of installing directly into kayak. These track clips slip into kayaks track and Transom Kit mounts onto track. |
Sale Price $14.99
|
|
Item # 33-0000
Propellers for 30lbs, 32lbs, 46lbs, 55lbs 56lbs, Thrust Trolling Motor for Island Hopper Trolling Motors Only. |
|
 |
Item # 83699
35ah AGM Battery 12volt Approx. size: 9" x 8" x 6" (may vary slightly by 1" on all side) Trolling motors require a 12v battery to operate. Depending on the pounds of thrust of the motor you choose, you may require a back up battery for longer range use. Battery range will vary due to size, weight and type of kayak in addition to kayaks load, wind and current. *Additional battery info Click Here |
Sale Price $89.99
|
|
Item # 88-4324
35ah AGM Battery & Battery Charger - 12volt Approx. size: 9" x 8" x 6" (may vary slightly by 1" on all side) Trolling motors require a 12v battery to operate. Depending on the pounds of thrust of the motor you choose, you may require a back up battery for longer range use. Battery range will vary due to size, weight and type of kayak in addition to kayaks load, wind and current. Battery charge for charging AGM & deep cycle batteries. *Additional battery info Click Here |
Sale Price $154.99
|
|
Double Click Video to Play
|
Images of Lure II Kayak
Lifting and lowering of trolling motor is as easy 1, 2, 3 . . . |
Transom Mount with Steering Handle Kits
Easy installation transom mount kits that are dependable and will fit new and older kayaks without rudders or foot pedals. Transom Mount trolling motors can be installed with a traditional surface set up and steering handle. Transom motor mount has been engineered to attach to kayaks built-in track with our track clips or to kayak with four stainless screws, eliminating any cut outs to the hull and any access hatches. No unsightly wires, just two flexible cables: one to the remote control box and one to the battery terminals. The motor and shaft are low in profile and compact in size making it easy for removal and storage.
Easy installation transom mount kits that are dependable and will fit new and older kayaks without rudders or foot pedals. Transom Mount trolling motors can be installed with a traditional surface set up and steering handle. Transom motor mount has been engineered to attach to kayaks built-in track with our track clips or to kayak with four stainless screws, eliminating any cut outs to the hull and any access hatches. No unsightly wires, just two flexible cables: one to the remote control box and one to the battery terminals. The motor and shaft are low in profile and compact in size making it easy for removal and storage.
Lifting Feature Allows the Lifting of Motor
All transom mounts tend to trail lower than the keel of the kayak making it difficult to navigate in weeded waters, where sea grass, lily pods and debris is floating, as well as, running a ground, beach casting and landing and during portage. To resolve this issue we added a remote lifting feature to lift the motor while, sitting in your kayak and clear obstacles.
All transom mounts tend to trail lower than the keel of the kayak making it difficult to navigate in weeded waters, where sea grass, lily pods and debris is floating, as well as, running a ground, beach casting and landing and during portage. To resolve this issue we added a remote lifting feature to lift the motor while, sitting in your kayak and clear obstacles.
Telescoping Steering Handle
Our system allows the kayak to steer using the telescoping handle. The steering handle is adjustable to meet the different kayak lengths. No altering of cables or kayak. The transom mounts are made from durable polypropylene composite for marine application, aluminum and stainless steel hardware. We provide stainless steel fasteners to prevent rust.
Our system allows the kayak to steer using the telescoping handle. The steering handle is adjustable to meet the different kayak lengths. No altering of cables or kayak. The transom mounts are made from durable polypropylene composite for marine application, aluminum and stainless steel hardware. We provide stainless steel fasteners to prevent rust.
Fresh & Saltwater Trolling Motors, 32 lbs, 46 lbs, 55 lbs Thrust of Power Available
We offer several models for fresh water and salt water use, and the Remote Controllers are IP54 and Trolling Motors are IP64: Splash Proof, Not Submersible.
We offer several models for fresh water and salt water use, and the Remote Controllers are IP54 and Trolling Motors are IP64: Splash Proof, Not Submersible.
Speeds: 5 Speeds Forward / 2 Speeds Reverse, Three Bade Propeller
The motors have a selectors switch, 1-5 speeds forward, 2 reverse, and 3rd speed for auto lift. The three blade machete propeller is included with 55lbs trolling motors. The two blade machete propeller are included with 46lb and 32lb trolling motors. The machete propeller allows for more torque to push the kayak forward in choppy waters or windy conditions, in addition, to cut through weeds and debris with minimal fouling. Remote Controllers are IP54, Splash Proof, Not Submersible.
The motors have a selectors switch, 1-5 speeds forward, 2 reverse, and 3rd speed for auto lift. The three blade machete propeller is included with 55lbs trolling motors. The two blade machete propeller are included with 46lb and 32lb trolling motors. The machete propeller allows for more torque to push the kayak forward in choppy waters or windy conditions, in addition, to cut through weeds and debris with minimal fouling. Remote Controllers are IP54, Splash Proof, Not Submersible.
Our Transom Power Drive Systems Are Guaranteed
|
Design, colors and images may differ from actual item.
Remote Controllers are IP54 and Trolling Motors are IP64: Splash Proof, Not Submersible. |
.
|
For sales and technical support, call (727) 501-3116
|
Battery Disclaimer Island Hopper Outboards is not responsible for the performance of any battery range. It is the sole responsibility of the consumer to choose the right battery and/or batteries.
|