Wired Variable Speed Control for Trolling Motors
Wired Variable Speed Control Kayak Motors Built with Smart Energy Conservation Modulator (S.E.C.M.)
Introducing a new breed of kayak motors integrated with (S.E.C.M.) circuit board. These electronic boards modulate the energy consumed by the trolling motor into mini pulses, making it possible to conserve up to 80% of battery reserve based on trolling speed chosen.
Micro Processor Sensing Unit
The Smart Energy Conservation Modulator (S.E.C.M), is built with the most advanced super H Bridge F.E.T power train technology and a micro processor that can detect an abnormal current load inconsistent with the motor amperage draw. The sensing micro chip module shuts down the motor in a fraction of a second, preventing the trolling motor and its circuitry board from damage and will auto reset itself again.
What causes an abnormal current load?
An abnormal current load is caused when a propeller gets fouled with sea grass, weeds, kelp, fishing lines or debris, causing the motor wires to heat up and shorting the control board and motor, and potentially destroying the motor.
Advantage of Smart Energy Conservation Modulator (Variable Speed Controller) Verse Conventional Trolling Motor
A conventional trolling motor, will use up as much energy as it is rated when choosing slow speed such as, 30 lbs thrust will draw 30 amps, 46 lbs thrust will draw 46 amps and so on. These conventional motors regulate the speeds, by taking the energy from the battery and cycling it through a rheostat in the motor, to delivery a slower speed by converting that energy into wasted heat and into the cool water.
The Smart Energy Conservation Modulator senses the selected trolling speed and calculates the power draw required by the motor through a series of complicated steps, then delivers the exact amount of amperage needed by the motor. This process saves the otherwise wasted amperage and sends the amperage's back to the battery, thus extending a single charge, from 3 hours to 8 hours.*
While S.E.C.M maximizes the amount of energy drawn at lower speeds, it will also sense the greater demand for higher speed and by pass the modulation mode (trickle amperage delivery system) allowing the motor to go full speed. However, at wide open throttle, no substantial amperage savings will be gained .
*These rates are based on 12v 75ah battery.
Introducing a new breed of kayak motors integrated with (S.E.C.M.) circuit board. These electronic boards modulate the energy consumed by the trolling motor into mini pulses, making it possible to conserve up to 80% of battery reserve based on trolling speed chosen.
Micro Processor Sensing Unit
The Smart Energy Conservation Modulator (S.E.C.M), is built with the most advanced super H Bridge F.E.T power train technology and a micro processor that can detect an abnormal current load inconsistent with the motor amperage draw. The sensing micro chip module shuts down the motor in a fraction of a second, preventing the trolling motor and its circuitry board from damage and will auto reset itself again.
What causes an abnormal current load?
An abnormal current load is caused when a propeller gets fouled with sea grass, weeds, kelp, fishing lines or debris, causing the motor wires to heat up and shorting the control board and motor, and potentially destroying the motor.
Advantage of Smart Energy Conservation Modulator (Variable Speed Controller) Verse Conventional Trolling Motor
A conventional trolling motor, will use up as much energy as it is rated when choosing slow speed such as, 30 lbs thrust will draw 30 amps, 46 lbs thrust will draw 46 amps and so on. These conventional motors regulate the speeds, by taking the energy from the battery and cycling it through a rheostat in the motor, to delivery a slower speed by converting that energy into wasted heat and into the cool water.
The Smart Energy Conservation Modulator senses the selected trolling speed and calculates the power draw required by the motor through a series of complicated steps, then delivers the exact amount of amperage needed by the motor. This process saves the otherwise wasted amperage and sends the amperage's back to the battery, thus extending a single charge, from 3 hours to 8 hours.*
While S.E.C.M maximizes the amount of energy drawn at lower speeds, it will also sense the greater demand for higher speed and by pass the modulation mode (trickle amperage delivery system) allowing the motor to go full speed. However, at wide open throttle, no substantial amperage savings will be gained .
*These rates are based on 12v 75ah battery.
Wired Variable Speed Control for Various Trolling Motors
Our Variable Speed Trolling Motors Are Guaranteed
For sales and technical support, call (727) 501-3116
Design, colors and images may differ from actual item.
Remote Controllers are IP54 and Trolling Motor are IP64: Splash Proof, Not Submersible.
Remote Controllers are IP54 and Trolling Motor are IP64: Splash Proof, Not Submersible.
|
Battery Disclaimer Island Hopper Outboards is not responsible for the performance of any battery range. It is the sole responsibility of the consumer to choose the right battery and/or batteries.
|
Hobie is a registered trademark. Island Hopper Outboards manufactures accessories to retrofit a many numerous kayak on the market, Island Hopper Outboards accessories are not a Hobie branded products. We do not sell or make any claim that these accessories are manufactured by Hobie.